|Color:||Sliver And Yellow||Material:||Industrial Reinforced Nylon Plastics|
|Controlling Distance:||≥100m/can Be Customized 250m/500m|
reinforced Industrial Wireless Remote Control,
433MHz industrial wireless relay,
433MHz industrial radio remote control
Welding robot wireless remote control, the complete set includes 1 transmitter + 1 receiver, the remote control distance is provided according to 100 meters, the receiver end is designed for RS485 output, and the 485 interface of the controlled end PLC communicates with the Moudbus protocol, except for emergency stop. 1 normally open relay output on the receiver side, and other button functions are output as digital signals through the data interface RS485.
Transmitter button layout and function description
1) Gun up, gun down, gun back, gun in, the layout is two three-position self-resetting levers, each of which is three positions in the front, middle and back, the middle is the zero position, the zero position does not correspond to the output, two front and rear Each position corresponds to 1 normally open relay output at the receiver end;
2) 2 buttons with indicator light, self-reset mode, both press once to turn on the indicator light, press the second time to turn off the indicator light, each button corresponds to a fixed-value jog mode digital signal on the receiver side Output
3) Nine buttons without indicator lights, all in jog mode, and no interlock logic is set between each other, which is convenient for the back-end PLC to customize various logics. Each button corresponds to a fixed value point on the receiver side. Digital signal output in dynamic mode;
4) 2 indicator lights, 1 power indicator light, red light on low battery, 1 signal light, normal operation button flashes green light to indicate.
5) Start+emergency stop mushroom head knob, start layout is rotary switch or self-locking button, emergency stop is European emergency stop mushroom head type, self-locking hold mode, corresponding to 1 switch signal output. Start is to start the power switch of the transmitter itself, and at the same time, the output control loop of the receiver is turned on. At this time, the device at the controlled end is energized and the emergency stop is photographed, and all outputs can be cut off instantly. The start button on the transmitter side is turned off, the transmitter side power is turned off, and after 5 seconds, the receiver side can also emergency stop by itself to ensure safety!
This welding robot wireless remote control product model DHZ-2BZ9F2F2ZSD485 (receiver end DC24V / open environment 100 meters / 1 send 1 receive / RS485 Moudbus protocol) other voltages such as AC220V or AC380V, etc., will be adapted through external transformer conversion!
|Transmitter Function||LCD screen|
|Application||motor type gantry|
|Material||Industrial reinforced nylon plastics|
|Controlling distance||≥100m/can be customized 250m/500m|
1. Stable control signals will ensure no interference during use. The unique signal is encrypted and coded, and there is no interference when using multiple sets of remote controllers in an environment.
2. Stainless steel buttons and Industrial reinforced nylon plastics shell, more resistant to be broken and smudge.
3. The transmitter is sealed with silicone rubber ring, which is good waterproof.
4. Heartbeat packet detection:Once the transmitter is damaged or the signal is lost, the receiver will stop automatically.
5. The antenna is built inside to prevent it from being broken.
6. Each set remote control has unique ID identification code, even if the same frequency also does not interfere with each other.
1. Transmitter * 1 pcs
2. Receivers * 1 pcs
3. The receiver comes with 1m cable connector
4. Operation and Maintenance Manual
1. Due to transportation requirements, the product is not equipped with battery.
2. The function can be customized according to your requirements, please contact the supplier.
1. Customized logo and trademark are warmly-welcomed.
2. Good after-sale services offered.
3. 1 year warranty period, spare parts supply for free.
4. 100% QC inspection before shipment.
To provide quality products at the same time to improve after-sales support
An independent R & D and design company with ten years of technology accumulation, which can be quickly customized.
We have own assem- bling factory and mold factory.
Professional team to provide you with efficient service.
Contact Person: Mr. Zhu